Lemon Bottle — Lipolysis Solution
Injection & treatment protocol
Quick Reference
Overview
Lemon Bottle is applied using a point/grid subcutaneous injection technique across the targeted adipose area, rather than a single systemic dose. Small volumes are placed at evenly spaced points so the riboflavin, lecithin, and bromelain blend distributes across the treatment zone. Sessions are spaced 1–2 weeks apart to allow the metabolic and inflammatory response from the prior session to resolve before the area is re-treated.
Dosing & Reconstitution Guide
| Phase | Daily Dose | Units | Volume |
|---|---|---|---|
| Chin / submental area | 0.1 mL per point, ~1 cm grid spacing | 10–20 points | 2–4 mL per session |
| Abdomen (per zone) | 0.1–0.2 mL per point, ~1.5 cm grid spacing | 30–50 points | 6–10 mL per session |
| Flanks (per side) | 0.1–0.2 mL per point, ~1.5 cm grid spacing | 20–30 points | 4–6 mL per session |
| Thighs (per zone) | 0.1–0.2 mL per point, ~1.5 cm grid spacing | 30–50 points | 6–10 mL per session |
Reconstitution Instructions
Lemon Bottle is supplied as a ready-to-use sterile solution — no reconstitution is required.
Visually inspect the vial for particulates or discolouration; discard if the solution is compromised.
Draw the required volume using a sterile syringe and a fine-gauge needle (30–32G recommended for facial/submental areas, 27–30G for body areas).
Mark injection points in a grid pattern spaced approximately 1–1.5 cm apart across the treatment area.
Cleanse the area with an alcohol swab and allow it to air-dry before injecting.
Inject 0.1–0.2 mL subcutaneously at each marked point; avoid intramuscular or intravascular injection.
Apply gentle pressure with sterile gauze after each point; ice application post-treatment may reduce localised swelling.
This guide is for educational purposes only and is not medical advice. For research use only. Not for human consumption.
Supplies Needed
- ✓Lemon Bottle Vial (10 mL): 1 vial
- ✓Sterile 1 mL/3 mL Syringes: 5–10 syringes
- ✓Fine-Gauge Needles (27–32G): 10 needles
- ✓Alcohol Swabs: 10 swabs
- ✓Sterile Gauze: 1 pack
- ✓Sharps Container: 1
Dosing Protocol
Schedule
Sessions are spaced 1–2 weeks apart per treatment area, allowing local inflammation to resolve and released fat to be metabolised before the next session.
Session Count
Most protocols run 4–6 sessions per area, with visible contouring effects typically assessed starting from the 3rd session.
Technique
Use a consistent grid/point injection pattern (~1–1.5 cm spacing) for even distribution; avoid concentrating volume at any single point.
Storage & Handling
- ✓Store sealed vials in a cool, dry place away from direct light.
- ✓Once opened, refrigerate at 2–8 °C and use within the manufacturer's recommended window.
- ✓Do not freeze.
- ✓Discard if the solution becomes cloudy, discoloured, or contains visible particles.
- ✓Keep vials in their original packaging until use.
Important Notes
- ✓All products sold by JA Performance Peptides are intended strictly for laboratory research purposes and are not approved for human consumption, veterinary use, or therapeutic application. Not for human use.
- ✓Use a new sterile syringe and needle for each session; dispose of sharps properly.
- ✓Withdraw slightly before injecting to reduce the chance of intravascular placement.
- ✓Localised swelling, redness, or mild bruising at injection points is commonly reported and typically resolves within days.
- ✓Document treatment area, total volume, point count, and session date for consistency across the protocol.